WDM Bi-directional Fiber Converter / single fiber UP to 20Km. Pl


Cod Produs [4689]

Pentru amanunte suplimentare cu referire la: caracteristici, stoc, pret, termen de livrare, ale acestui produs, sunati la 0745.063.200 sau 0767.820.422 !

<< WDM 10/100 singlemode mediaconvertor, Internal Power Supply. Qub

WDM Bi-directional Fiber Converter / single fiber UP to 20Km. Pl >>

WDM Bi-directional Fiber Converter / single fiber UP to 20Km. Pl
Retelistica > Echipamente Active Si Pasive Pentru Retele LAN > Echipamente Active > Media Convertoare Pentru Fibra > Mediaconvertoare 10/100

Planet FT-8x - Fast Ethernet Bridge Media Converters
Planet FT-8x - Fast Ethernet Bridge Media Converters





  The PLANET FT-80X is Fast Ethernet Bridge 100Base-FX fiber to 10/100Base-TX shielded twisted pair (STP) converter. It supports selectable for half-duplex and full-duplex operations and supports a variety of fiber options. The converter auto-adapts to the highest level of performanta supported by the device connected to the STP port. When the device is a switch or a workstation that supports full duplex, the converter adapts to the full-duplex mode and provides an effective 200Mbps bandwidth. When the connected device is a hub or a workstation that supports only half duplex, the converter adapts to the half-duplex mode and provides the nominal 100Mbps bandwidth. An override switch provides total manual control over the half/full-duplex operation, in fiber-optic interface. The fiber port of converter operates at 1310 nm and uses ST, SC, MT-RJ, VF-45 or WDM connectors. Multi-mode models that support distances up to 2 km and single-mode models that support distances up to 15/35/50 km are available.
 
  The FT-80x series are with LFP (Link Fault Pass Through function) (LLCF/LLR) and the DIP Switch design. LLCF/LLR can immediately alarm administrators the problem of the link media and provide efficient solution to monitor the net. The DIP Switch provides disable or enable the LFP function.
 
  LLCF (Link Loss Carry Forward) means when a device connected to the converter and the TP line loss the link, the converter's fiber will disconnect the link of transmit. LLR (Link Loss Return) means when a device connected to the converter and the fiber line loss the link, the converter's fiber will disconnect the link of transmit. Both can immediately alarm administrators the problem of the link media and provide efficient solution to monitor the net.
Key Caracteristici:
   - Comply with IEEE802.3, IEEE802.3u 10/100Base-TX, 100Base-FX Standard
   - Connectors: One RJ-45 (Auto-MDI/MDI-X) Twisted Pair, EIA568
   - One Fiber-optic, 1310nm wavelength, connector-type and distance vary with model.
       - FT-806A20: Tx-1310nm, Rx-1550nm
       - FT-806B20: Tx-1550nm, Rx-1310nm
   - Data Transfer Rate:
       - TP: 10/100Mbps
       - FX: 100Mbps
   - Duplex mode support:
       - Full or half-duplex mode by Auto- Negotiation (TP)
       - Full or half-duplex mode by DIP-switch (FX)
   - LED indicators: PWR, FX LNK/ACT, FX FDX/COL, TP 100, TP LNK/ACT, TP FDX/COL
   - DIP-switch: 2 DIP-switches
       - Rear DIP-switch: FX duplex mode selection
       - Side DIP-switch: LFP (Link Fault Pass-through) mode selection
Specifications:
  Product:
 Protocol  IEEE 802.3u, 100Base-FX, 100Base-TX
 Dimensions  70 x 97 x 26 mm (W x D x H)
 Weight  0.2kg
 Power  5V DC, 2A, max.
  Connectors and Cables:
 Twisted Pair STP  100 m / 328 ft.
 Fiber-optic  Vary on model;
 X=1,2,3,4,5,6
 1:ST
 2:SC
 3:MT-RJ
 4:VF-45
 6 Single SC; WDM
 Multi-mode cable  50/125, 62.5/125 µm
 Single-Mode (SM) cable  9/125 µm
  Supported Distances and function:
 Twisted Pair STP  100 m / 328 ft.
 Multi-mode Fiber Optic  412 m / 1,350 ft. (Half-Duplex)
 2 km / 1.2 mile. (Full-Duplex)
 Single-Mode (SM)  412 m / 1,350 ft. (Half-Duplex)
 15 km / 9 mile. (Full-Duplex)
 35km / 21 mile. (Full-Duplex)
 50km / 31 mile. (Full-Duplex)
 Port Mode  TP: Half and Full Duplex, auto-negotiation
 FX: Half and Full Duplex via DIP switch
  Environmental:
 Temperature  0 to 50 °C
 Humidity  5-90% (non-condensing)
 Note :
FT-806A20/806B20 should runs in pair. It means you must connect FT-806A20 in one end another FT-806B20 in other end.
 
Traducere
Informatii Producator
Alte produse